Description:-
The MT8870 Tone Decoder is a kind of common used multifrequency decode IC product developed by the MITEL company. It has a working voltage of 5V. It is a compete DTMF receiver. After it received the DTMF signal, it will divide the signal into high frequency group and low frequency group and send the signal to the digital decoder which can figure out the key value then send it to the outside Bus via four lines( Q1, Q2, Q3, Q4) as the binary form.
Features:
Additional Information:
Product Details:
Working voltage | 5V DC |
Board size | 49 x 41.5 (mm) |
Recording time | 6K time 75 seconds, 8K for 60 seconds |
Chip operating frequency | 6KHZ and 8KHZ optional |
Audio signal input channel | Microphone Input And Analog Signal Inputs |
Specifications:
Additional Information:
Description:
This voice record/playback device is based on ISD1820 chip, which can record/playback multiple-message. It can offer true single-chip voice recording, non-volatile storage, and playback capability for 8 to 20 seconds. For the sampling rate of 3.2KHz it can record for the total duration of 20 seconds.
Features:
If you want change the record duration, an external resistor is necessary to select the record duration and sampling frequency, which can range from 8 – 20 seconds (4-12kHz sampling frequency). This voice record module provides default connect to a 100k resistor through P2 by short cap. So the default record duration is 10s.
Additional Information:
Use TM1638 digital tube drive chip to drive common cathode LED digital tube.
This module for the chip TM1638, set the above three kinds of single chip microcomputer common peripheral circuit, the biggest characteristic is to simply take microcontroller three IO mouth can drive, scanning display and key scan don't need microcontroller intervention, only need to register to display data related to reading and writing or testing buttons, save MCU resources.
Features:
Additional Information:
Description:
This is a 5V 4-Channel Relay interface board, Be able to control various appliances, and other equipments equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Additional Information:
Technical Specifications:
Note: Do not mix the "negative" of the left and the right output channel with "negative" of the power supply, otherwise it will burn the IC.
Additional Information:
Description:
For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter.
Technical details
Additional Information:
Description:
Rotation of the rotary encoder may be counted by the positive rotation direction and a reverse direction pulse frequency output during rotation potentiometer not count this rotation count is not limited. With buttons on the rotary encoder can be reset to the initial state, that starts counting from 0.
Specifications:
General
Model: Keyes KY-040
- Material: Glass fiber + plastic + iron
- Compatibility: Ardunio
Electronic Components
Architecture: Arduino
- Operating Voltage: 5V
Weight and Size
Product Weight: 5 g
- Package Weight: 0.055 kg
- Package Size(L x W x H): 7.0 x 5.0 x 2.0 cm
Package Contents
Package Contents: 1 x Module
Rotation of the rotary encoder may be counted by the positive rotation direction and a reverse direction pulse frequency output during rotation potentiometer not count this rotation count is not limited. With buttons on the rotary encoder can be reset to the initial state, that starts counting from 0.
Additional Information:
Description:
DS1307 is a real-time chip of DALLAS company,which adopt I2C protocal to communicate with SCM, and there was this kind interface on Arduino, therefore is very convenient to link with each other. DS1307 have a programmable waveforms output, it can be used to drive LED lights, or trigger a certain event as a break off, but be careful when you use it to take some kind of high power module. We design the real clock module to pin out the I2C interface of Ds1307 and programmable waveforms output interface SQW are connected, but usually we will only use the I2C interface to realize basic set the clock/read function. Note, this module must be installed on the battery can work normally. The battery is button batteries (type CR2032 will be better), the positive upward:
This tiny module embraces DS1307 time module, DS18B20 temperature module and AT24C32 storage module. DS1307 and AT24C32 are connected to IIC bus. And DS18B20 can be visited via DS pin.
Features:
Additional Information:
Specifications:
Additional Information:
Specification:
Additional Information:
Product Description
This is a Joystick module that has X,Y analog outputs and has a switch that detects button press. The joystick is made up of two passive potentio-meters (variable resistors) and a push button and therefore can be used at any standard voltage levels.
Applications
Additional Information:
Features:
Additional Information:
The output frequency is adjustable:
Additional Information:
Product Description
These displays were used in old Nokia 5110/3310 cell phones (before the smart-phone fad turned every cell phone into a TV). It’s a 84×48 pixel monochrome LCD display. These displays are small, only about 1.5″ diagonal, but very readable and come with a white backlight. This display is made of 84×48 individual pixels, so you can use it for graphics, text or bitmaps. These displays are inexpensive, easy to use, require only a few digital I/O pins and are fairly low power as well
To drive the display, you will need 3 to 5 digital output pins (depending on whether you want to manually control the chip select and reset lines). Another pin can be used to control (via on/off or PWM) the backlight – the backlight LEDs are wired to a transistor.
The display driver is a PCD8544 chip, and it runs at 3.3V so you’ll need a 3V supply handy (you don’t need that much current though, maybe 10mA tops). Logic levels must be 3V to prevent damage but we include a free level shifter chip so you can easily connect it to 5V logic such as an Arduino.
Specifications of LCD 5110
Feature:
Additional Information:
Additional Information:
Features
Technical Details
Introduction
PCA9685 16-Channel 12-Bit PWM Servo Driver can help a lot when there are insufficient PWM output pins for the MCU in your project. The only condition is that the main control chip supports I2C communication, which means enabling the communication between the chip and PCA9685, so as to control multiple servos simultaneously.
Additional Information:
Additional Information:
Additional Information:
Features:
Additional Information:
Product Details:
Size | 4.1 x 2.4cm |
Power supply | 4.5V to 5.5V, 3.3V voltage regulator circuit board |
Communication interface | Standard Spi Interface |
Supports | Micro Sd Card (more Than Equal To 2g), Micro Sdhc Card (less Than Equal To 32g) (high-speed Card) |
Control Interface | A total of six pins (GND, VCC, MISO, MOSI, SCK, CS) |
Description:-
To use with an Arduino, connect GND to ground, 5V to 5V, CLK to pin 13, DO to pin 12, DI to pin 11, and CS to pin 10. Then you can use the Arduino IDE''s SD library which supports FAT and FAT32 SD cards
Additional Information: