|Minimum Order Quantity||01 Piece|
|Transmit Power||40 mA|
ZigBee modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors. The most common factor in determining whether to use ZB is the potential need to tie-in with other ZigBee-compatible networks or mesh networking. If this is not a requirement, the series 1 802.15.4 modules may be perfectly suitable for your project.
Note: Because XBee modules have 2 mm pin spacing, we recommend one of our adapter boards for each module. Our adapter boards provide several advantages to the XBee modules such breadboard-friendly standard 0.1 inch pin spacing, mounting holes, and easy-to-solder connections. Even if you are communicating point-to-point without a PC, we still recommend that you always have at least one XBee USB Adapter Board (# 32400) so you can easily configure and test each XBee module prior to putting it in a point-to-point application.
|Data Rate||250 kbps|
|Operating Supply Voltage||2.7 V to 3.6 V|
XBee 802.15.4 modules are easy to use, reliable RF devices. The 802.15.4 XBee modules provide two friendly modes of communication – a simple serial method of transmit/receive or a framed mode providing advanced features. XBees are ready to use out of the package, or they can be configured through the X-CTU utility or from your microcontroller. These modules can communicate point to point, from one point to a PC, or in a mesh network.
Digi International move both the Series 1 and Series 2 functionality to the S2C hardware. This new variant is functionally and OTA compatible with the legacy XBee S1 802.15.4 and introduces several major advantages including reduced power consumption, better range and receive sensitivity, support for over-the-air firmware updates, and provides an upgrade path to DigiMesh® or ZigBee® mesh protocols if desired.
This XBee model is as replacement/upgrade for the XB24-AWI-001.
XBee ZB / ZigBee modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors.
The ZB modules requires considerable setup and configuration. XBee Series 1 (802.15.4) and XBee Series 2 (ZB / ZigBee) modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules.
Digi International move both the Series 1 and Series 2 functionality to the S2C hardware. This XBee S2C model is as replacement/upgrade for the XBP24BZ7WIT-004.
|TRANSCEIVER CHIPSET||Silicon Labs EM357 SoC|
|DATA RATE||RF 250 Kbps, Serial up to 1 Mbps|
|TRANSMIT POWER||63 mW (+18 dBm)|
|INDOOR or URBAN RANGE||300 ft (90 m)|
|FREQUENCY BAND||ISM 2.4 GHz|
|SUPPLY VOLTAGE||2.7 to 3.6V|
XBee Pro 63mW RPSMA - Series 2C (ZigBee Mesh) is ZigBee RF modules provide cost effective wireless connectivity to electronic devices. They are interoperable with other ZigBee PRO feature set devices. Embedded ZigBee RF modules provide OEMs with a simple way to integrate mesh technology into their application. The XBee-PRO ZigBee RF Modules provide wireless connectivity to end-point devices in ZigBee mesh networks. Using the ZigBee PRO Feature Set, these modules are inter-operable with other ZigBee devices. With the XBee, users can have their ZigBee network up-and-running in a matter of minutes without configuration or additional development.
XBee and XBee-PRO ZigBee modules are ideal for applications in the energy and controls markets where manufacturing efficiencies are critical. The Serial Peripheral Interface (SPI) provides a high-speed interface and optimizes integration with embedded microcontrollers, lowering development costs and reducing time to market. Products in the XBee family require little to no configuration or additional development. Programmable versions of the XBee and XBee-PRO ZigBee module make customizing applications easy. Programming directly on the module eliminates the need for a separate processor. Because the wireless software is isolated, applications can be developed with no risk to RF performance or security.Specification of XBee Pro 63mW RPSMA - Series 2C (ZigBee Mesh)
|frequency band||2400 - 2483.5 MHz|
|Air data rate||up to 2Mbps.|
|Application||emote control, home security & alarm, telemetry, personal data logging, tire pressure monitoring, wi|
|Frequency||433/868/915MHz ISM bands|
|Model Number||RFM23BP RF Transceiver|
|RF Data Rate (bps)||data rate of 0.123 to 256 kbps|
|output power range||+30 dBm Max|
NRF24L01P + PA + LNA wireless module core Norway NORDIC company's latest high-performance wireless
Digital transmission chip NRF24L01 + with the Division of Professional Design professional full two-way RF power amplifier high power PA and LNA chip, RF switches, bandpass filters, etc., makes effective communication distance greatly expand.
RF part, the Secretary has done a lot of optimization matching debugging, the emission efficiency to achieve the highest harmonic minimum
NRF24L01P + PA + LNA wireless module of RF interference to the external equipment reaches a minimum, while not susceptible to interference from other devices, greatly Uploader
High stability of the work.
NRF24L01P + PA + LNA wireless module integration is extremely high, the size of only 41mm * 15.5mm, convenient embed.Item Specifications:
This is the XBee XBP24CZ7WIT-004 module from Digi. The new Series 2C improves upon the power output and data protocol of the Pro Series2. Series 2C modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
The XBee/XBee-PRO ZB (S2C) introduces the SPI serial interface to Digi’s through-hole ZigBee radio. Please refer to the XBee/XBee-PRO ZB (S2C) product manual for more information.